|
Post by Marathonman on Oct 6, 2019 9:36:59 GMT -6
I have been working on CNC bids in my area for the Bearing part i need. have sent out three bids requests so hopefully i will hear something Monday or Tuesday. i also found a local supplier for a 17.5 mm drill bit i need to drill out the slip ring. i can then cut to length to fit on the rotor shaft. MM
|
|
|
Post by creasysee on Oct 7, 2019 9:56:54 GMT -6
Epoxying. On the bottom side the same plate as top side, but without any contacts. Epoxy through the holes in the top board flooded the interior and both boards stuck together. Later I will finish the places where the clamps are installed. Both boards must be strictly parallel. Alignment was done with clamps.
|
|
|
Post by cornboy on Oct 7, 2019 18:43:57 GMT -6
Hello all, just finished my new Part G+R, already pulled it apart and modified the brush width, may have to do it more, but it's putting out a reasonable signal now, hooked up to 24v bulbs for testing.
Pics attached.
Regards Cornboy.
|
|
|
Post by cornboy on Oct 7, 2019 18:45:30 GMT -6
|
|
|
Post by Marathonman on Oct 8, 2019 7:26:53 GMT -6
Creasysee; can not view the pic on the thread or in Google. try Postimage.org, they seem to just work for me.
Cornboy; Interesting setup, it looks like a lot of time and effort was involved. i do though have many concerns about that scope shot but i will save that for a later date. keep up the good work fellas.
it will not be much longer for myself to be back in the building status. just a few more parts and my part G is complete. i have multiple appointments today so i hope everything goes well. Regards, MM
|
|
|
Post by cornboy on Oct 8, 2019 15:25:18 GMT -6
MM, the wave form is not ideal, but better than the first signal i had, i am pretty sure i know how to improve it.
At least it is all in positive territory, 180 apart, and not too fuzzy or spiky.
Good luck, with your appointments.
Regards Cornboy.
|
|
|
Post by Marathonman on Oct 8, 2019 17:16:22 GMT -6
Most appreciative Cornboy, and yes they did turn out well which will have me occupied for the next week or so tying loose ends. True, i do agree with your statement yet the massive flat top with the dive and rise at the bottom is what has me worried. i am sure you have your plan of attack.
have you tested your overall inductance of part G and is it within your current guidelines of reduction??? i am just curious as 5 winding's a tick of the brush seams an awful lot of drop. of course your part G is not that large to start with so i am rooting for ya ! my part G has less winding's as each loop is 13 inches which is quite a lot of core material plus the fact that i can change the diameter of my brushes if need be which is a feature I absolutely wanted to have. in for less inductance window, out for larger inductance window. i do not have to have the exact inductance for my primaries as long as i am in the ball park all i have to do is dial it in. this is just an extra ability to fine tune the balance. see there actually was a method to my madness, ha, ha, ha!
good to have you guys aboard.
Regards, Marathonman
|
|
|
Post by Marathonman on Oct 17, 2019 20:44:23 GMT -6
I just wanted to check back with you Cornboy if you have had any improvements in your wave form of part G. i was able to pick up a piece of 3/4" plywood for the epoxying of part G's wires. i am not to sure about using wood as it might flex causing a wavy finish once compressed down. maybe with a thin plate of metal below the wood would be better as i do not have thick on hand nor the money for one. MM
|
|
|
Post by cornboy on Oct 17, 2019 21:32:30 GMT -6
Hey MM, have been spending all my spare time cleaning up after the bushfires, taking 4 ute loads to the tip so far.
Hope to get back to it soon.
Regards Cornboy.
|
|
|
Post by creasysee on Oct 27, 2019 15:49:02 GMT -6
Hi builders! I'm updating the status. Bearings are installed on the top and bottom boards: Plates for primary and secondary are cutting: Regards, creasysee
|
|
|
Post by Marathonman on Oct 27, 2019 21:34:49 GMT -6
emmm, yummy, i love laminations. MM
|
|
|
Post by Marathonman on Nov 8, 2019 15:38:51 GMT -6
I hate to be the bearer of bad news but Unfortunate circumstances transpired this week is forcing me to bow out of my pursuit of the Figuera device. the new owners of the property where i live are refusing to work with Veteran programs to help in my financial blight even though i have the funding lined up, i was informed today i must move. the only place i have available to me has storage for clothing only and little else other than personal items. i am literally being forced to sell everything i own as i have no other choice in the matter or other avenues to pursue as in short term storage. this has literally been my dream come true to pursue this device and i have put every ounce of energy, time, money i have to advance this into reality. apparently the powers that be have decided to take yet another of my dreams away from me which is literally destroying me, ripping my entire sole to the core. even as i write this being a man, i can not hold back the tears from the one thing in my life that gave me hope and passion is being ripped from my possession yet again.
i will hold off on making definite decisions as i know things and miracles do happen when you least expect it. as of right now if things do not change i will be forced to abandon my pursuit of the Figuera device which will force me to close down this website as there will literally be no reason for it to exist. i have given my heart and sole to this device in my pursuit in the last 6 years of not only a dream come true but a chance of a lifetime to show people of this world there is still people that care and want to make a difference.
with much regret, sorrow and pain. Regards, Marathonman
|
|
|
Post by Marathonman on Nov 14, 2019 12:30:01 GMT -6
I have decided to keep this website up just to piss off those lousy Trolls and paid shills on EF AND OU that were probably doing a happy dance like no tomorrow. i hope it can still benefit others also that are pursuing the Figuera device. just maybe those boneheads might learn something but i doubt it.
here is an update to the situation i am in. it seems i will be able to at least save all my tools and Figuera device as a close friend of mine that i have done so much for saved the day by offering a few months of storage. so for the time being all is not lost and hopefully i can get my life together again to finish what i started. this device means everything to me so the first chance i get to continue i will jump on it. i am only lacking a few parts to get me to the point i can test so the likely hood of me finishing is very high.
I do apologize to everyone for the blunder i put myself through and i hope i can recover to continue my quest to educate the public on the feasibility of free energy.
Regards, Marathonman
|
|
|
Post by Marathonman on Nov 14, 2019 13:27:05 GMT -6
Here i will present FACTS to the Figuera device to all those that still think this device will not work.
FACT; We live in a perpetual motion machine that will continue to rotate our earth for billions of years when we are lone gone. FACT; Clemente Figuera had a working device in 1902 and presented a working model to the patent office. FACT; Clemente Figuera had a working device in 1908 and presented that working model to the Barcelona patent office. FACT; the conservation of energy does not pertain to a motional electric field and being so can not be shielded like that of gravity. FACT; the inverse square law/rule pertains to all fields/forces including magnetic fields FACT; an free standing electromagnet can only project out a field the length of the core it's self. FACT; an increase in voltage permits more current to flow. FACT; current flows from negative to positive. FACT; reducing resistance increases efficiency. FACT; resistors or resistance waste potential in the form of heat that is none recoverable. FACT; using multiple winding's reduces resistance and increases efficiency of the electromagnet increasing it's reaction time considerably. FACT; current travels in the same direction it was traveling in when released from it's stored state in the magnetic field. FACT; energy or potential is kinetic energy and retains it's spin direction irregardless of of how it was stored. FACT; inductors and coils store and release potential. FACT; inductors or coils release potential will add to an existing potential in a system raising the overall potential. FACT; changing the magnetic flux to current ratio will change the flow of current. FACT; opposing fields will increase the magnetic field line pressure compressing the lines of force to match that of a standard generator. FACT; opposing magnetic fields will never link to each other like that of a transformer. FACT; reducing or increasing the magnetic fields will create EMF in accordance with Faraday's laws of induction. FACT; secondary coils with current flowing will produce a Lenz law field that will oppose the change that created it. FACT; increasing the magnetic lines of force will increase the output. FACT; opposing fields can and will split an inductor in two halves which allow it to control current flow of two feeds. FACT; any DC potential given a rise and fall of current will attain a frequency thus will fall under inductive reactance. FACT; opposing primaries can and will induce virtual motion into a stationary secondary. FACT; Clemente Figuera did power his house lights, a 20 kilowatt motor and the street lights in front of his house with his device that was certified by the patent office to be in working condition that did what it said it did. BOTH TIMES !
These fact can NOT be denied by anyone which are directly applicable to the Figuera device. sure you can choose to be a paid misinforment, a paid shill and a general piece of crap like on EF and OU but that is your sick problem all together, not the people that choose to believe in real facts. any sane non lazy person that got off their butts to test what i have posted knows the real truth. isn't that right Citfa.
There is no burden of proof needed as Figuera already proved it TWICE. the burden of proof lies on the morons screaming it doesn't work. prove to me that it doesn't work or shut up and leave all the people pursuing this device in peace. oh, that's right you will not because your sorry useless pieces of crap that are to lazy from the money you get from Big Oil Companies that pay you to spread BS.
i have posted my knowledge from research freely to the public and demand absolutely nothing in return. i have and will NEVER EVER post things or information that purposely or knowingly misinforms the readers, followers and builders. i am now and will always be true to this cause and will help anyone that wants to pursue this device in any way i can. Regards, Marathonman
|
|
|
Post by creasysee on Nov 30, 2019 13:35:26 GMT -6
Hi all. I finished collect parts and start to build a part G. I think I can finish it in one month or so.
Regards, creasysee
|
|