|
|
Post by Marathonman on Dec 22, 2019 14:08:56 GMT -6
Since i find that many people really do not know how a generator works it would be a good reference point to view and study this video on you tube. even though this video is old it is still very much relevant. i am not insinuating people on this site do not know but just as a good starting point or reference of information.
Voltage Regulator
As the name implies, this component regulates the output voltage of the generator. The mechanism is described below against each component that plays a part in the cyclical process of voltage regulation.
(1) Voltage Regulator: Conversion of AC Voltage to DC Current – The voltage regulator takes up a small portion of the generator’s output of AC voltage and converts it into DC current. The voltage regulator then feeds this DC current to a set of secondary windings in the stator, known as exciter windings.
(2) Exciter Windings: Conversion of DC Current to AC Current – The exciter windings now function similar to the primary stator windings and generate a small AC current. The exciter windings are connected to units known as rotating rectifiers.
(3) Rotating Rectifiers: Conversion of AC Current to DC Current – These rectify the AC current generated by the exciter windings and convert it to DC current. This DC current is fed to the rotor / armature to create an electromagnetic field in addition to the rotating magnetic field of the rotor / armature.
(4) Rotor / Armature: Conversion of DC Current to AC Voltage – The rotor / armature now induces a larger AC voltage across the windings of the stator, which the generator now produces as a larger output AC voltage.
This cycle continues till the generator begins to produce output voltage equivalent to its full operating capacity. As the output of the generator increases, the voltage regulator produces less DC current. Once the generator reaches full operating capacity, the voltage regulator attains a state of equilibrium and produces just enough DC current to maintain the generator’s output at full operating level.
When you add a load to a generator, its output voltage dips a little. This prompts the voltage regulator into action and the above cycle begins. The cycle continues till the generator output ramps up to its original full operating capacity.
as you can read it takes a certain amount of pressure in the exciting/inducing system to produce a certain amount of magnetic field. once the field is at it's maximum as per the amount of current the exciters/inducers current draw is reduced to just the IR2 losses. this is the equilibrium spoken from above where the system is producing more then the exciters/inducers and the load combined. the exciters/inducers are no longer a load on the inducing system except for the IR2 loss replacement. the pressure in the exciting/inducing system is still being circulated throughout that system as that pressure maintains the magnetic field present. the secondary feedback is there to make sure that pressure in the exciting/inducing system is maintained at all times replacing losses when necessary.
the Figuera device is one and the same except one is rotating with motoring reverse torque that requires massive power to rotate and the other is stationary that moves the massless, weightless field from side to side. in the Figuera device part G is the AVR which regulated the amount of current flowing to the inducers and to regulate the secondary feed back into the system.
Regards,
Marathonman
|
|
|
|
Post by Marathonman on Dec 27, 2019 12:48:48 GMT -6
One needs to remember like the Adam Trombly device Figuera's device uses a duel toroidal field that compresses the field lines to match that of a high intensity field of a standard generator. it then increases one and reduces the other to achieve a sweeping action over the secondary. the whole key is proper compression and sweep of the fields.
out world has been spinning for millions of years and there is not a big guy up there spinning it for us. we live in a perpetual machine fore which the ney sayers say we do not live in. ignoring these fact will keep humanity in the stone ages.
free energy is viable whether you choose to ignore this fact is entirely up to you. embrace it and change humanity.
Regards,
Marathonman
|
|
|
|
Post by Marathonman on Dec 27, 2019 13:00:05 GMT -6
I would like to thank our newest member Ricardo for joining the ranks. if you have the time please tell us a little about yourself and what you would like to achieve. this is the best place on the net for Figuera information and i hope you enjoy all that has been posted. if you have any questions please feel free to ask away.
together we can change the world.
Regards,
Marathonman
|
|
|
|
Post by creasysee on Jan 5, 2020 3:36:03 GMT -6
Happy New Year!
Regards, creasysee
|
|
|
|
Post by Marathonman on Jan 6, 2020 10:49:19 GMT -6
Happy holiday folks, hopefully this year we can finish our builds and show the world free energy does exist. my end is looking better and i am confident i will have money flowing in in a few weeks. i can then rejoin the rest of you in the building process. i am so eager to finish after so much hardship i have had over the last few years. 2020 will be my year to prosper as i hope all the rest of you will also.
Regards,
Marathonman
|
|
|
|
Post by Admin on Jan 6, 2020 11:14:05 GMT -6
I would like to give a warm welcome to our newest member in our Figuera quest. Greybeardmike joined our group and i hope the information i have posted will benefit you very well. please fell free to ask any question after reviewing what has been posted.
Welcome to the best Figuera web site on the net.
Regards,
Marathonman
|
|
|
|
Post by Marathonman on Jan 9, 2020 13:41:08 GMT -6
If anyone is curious i will be getting my income tax back in the near future and MM will be back in the saddle again. also have a new job and and residence lined up as well as getting my drivers licence renewed tomorrow. it's time to get my Sheite together and lead by example.
Regards,
Marathonman
|
|
|
|
Post by creasysee on Jan 12, 2020 12:51:29 GMT -6
a motor in the system of 20 hp yet makes no mention of it being used. so as the original replicator and i were discussing at one time that the motor was connected to supply feed back on the secondary to keep the timing in check. it seems that with just a resistive load the secondary timing is off at almost 90 degrees there of and as such will cause the secondary feedback into part G will also be off as well. this phase mismatch will not introduce the proper amount of feedback required of the system at the right time which will not allow the system to self sustain and also the output to suffer dramatic reduction. Hi MM, In my opinion, Figuera was too smart for that. I believe he would have used an extra brush offset by 90 degrees. It's useless to turn a 20 hp motor too clueless for him. I think ( it's only my opinion) that the device will not work effectively on an active load. I still can't explain it somehow, a picture in my head has not yet fully developed in this context. Regards, creasysee |
|
|
|
Post by Marathonman on Jan 13, 2020 9:52:35 GMT -6
So then you have to ask yourself what would you do if you have advanced the timing with a brush and the timing is the other way as with just a resistive load. if you account for it by moving the brush it is permanent. then you have an inductive load the timing is out again and you have to adjust for the off timing which is ridiculous and a pain in the arse. the motor helps keep the timing intact no matter what type of load. this information was from the original replicator that has a running device as we speak that shared with me a lot of info and he has not miss lead me only lacking information on the feed back and other areas that i have extensively research over the last 6 years. take it for what it is worth, all researchers need to keep an open mind when dealing with uncharted territory as status quo has been shown to be 180 out of the truth.
the reluctance path through air is very important as it helps with the regulation of primaries magnetic field.
Regards,
Marathonman
|
|
|
|
Post by Marathonman on Jan 13, 2020 10:12:50 GMT -6
I have been in contact with UFOP on occasion and he has enlightened me to another researcher on EF that is attempting the Figuera device yet has strayed way beyond the patent and is NO longer the Figuera device.
a statement from the researcher to the fact that the primaries never go into the negative as always positive and there for can not produce a proper AC wave form in the secondary. this is the most completely ridiculous statement i have EVER HEARD. there is NO negative anywhere in out universe let alone in a standard AC wave form as the AC stands for alternating which means it travels in one direction then reverses to the other direction. there is NO NEGATIVE anywhere in an AC wave form so the lack of understanding AC wave form rears it's ugly head again.
in a standard generator the secondary is rotated through a NS field then through a SN field as the magnetic fields of both are in opposite direction which will cause the reverse current flow in the secondaries and at NO TIME is it EVER NEGATIVE.
in the Figuera device we have the exact very thing taking place as both opposing primaries have magnetic fields in the opposite direction that occupy the secondary one at a time then the magnetic field is removed. the secondary is exposed to two magnetic fields that are in opposite direction and again never in the negative just like a standard generator. it is these ridiculous statements i tend to laugh at because he obviously doesn't understand AC let a lone a standard generator. the Figuera device fulfills the exact requirements as a standard generator by compressing the magnetic fields to match that of a standard generator high intensity fields then reduces one and increases the other to get the sweeping action across the secondary which occupy the secondary one at a time. two oppositely directed fields are the same as a standard generator 150 years ago as well as today.
“Doubt is an incitement to research, and research is the path to true knowledge".
A truth’s initial commotion is directly proportional to how deeply the lie was believed. It wasn’t the world being round that agitated people but that the world wasn’t flat. When a well-packaged web of lies has been sold gradually to the masses over generations, the truth will seem utterly preposterous and its speaker a raving lunatic. – Dresden James
In a time of universal deceit, telling the truth is a revolutionary act. – George Orwell
Contempt, prior to complete investigation, enslaves men to ignorance. – Dr. John Whitman Ray
it seems there is a lack of proper research out there that is hampering the understanding not just the figuera device but other free energy deices as well. lack of proper research will bite you square in the ass my friend.
Regards,
Marathonman
|
|
|
|
Post by cornboy on Jan 13, 2020 19:16:17 GMT -6
Hi Skyrob, you can try Eurton elecrtic. Go to parts store and select commutators.
Regards cornboy.  |
|
|
|
Post by Marathonman on Jan 14, 2020 9:25:37 GMT -6
"Just a note that you are reading patent wrongly in respect of “G” needing to contact with two contacts Figuera meant that one contact on supply and other on “R” And those must not disconnect from DC at any given time." And you would be entirely incorrect as it is YOUR INTERPRETATION that is wrong. part G's positive brush has to make contact with more then one contact to avoid sparking and interruption of current flow. also it states specifically in the patent that "R" is drawn in it's elementary manor to understand the entire device. "R" does NOT EXIST AT ALL as it is the Inductive Reactance of the wire around the core and i am sick of explaining this multiple times to someone that can not understand apparently. also please if you will try to explain to me just how you plan on looping the secondary feed back into part G to be regulated by part G as well as the starting power supply without a brush feed back.  please enlighten us on your years of research, bench work and experience on the Figuera device. NO, i will no longer help anyone that doesn't take the time to read all the information and reread if you do not understand it. and for anyone's information the original replicator was my mentor that has a 5 kilowatt device running for the last three years that used an alternator for part G who by the way had to go underground from the suits showing up at his house so to protect his family he stopped posting and sent his device out of state temporarily. so just go ahead and build what you feel like building because you do not listen to anyone anyways. if people build according to the Patent then i will answer questions otherwise you are on your own. sorry but i do not have the time and or patience to baby sit all the way through this build as i have a ton of problems in my life right now. good luck, Marathonman |
|
|
|
Post by Marathonman on Jan 15, 2020 8:36:20 GMT -6
Having the ability to interpret and understand a patent is entirely different. when the Patent specifically states that "R" which is just a representation of some resistance withing Part G yet people insist it exists is beyond me.
do you not understand what happens when a person introduces a free energy device, they are lucky if they do not get murdered or beat up. the guy happens to have a family and is protecting them from harm. the only reason i cam forward is i am single and can care less if they take me out as i have brought this info forward to the masses and will continue until the device is running for all the world to see.
the reason people are experimenting is because all the entire information has not been released and it has taken me some time to figure these things out.
Using a magnetic field to control current flow is by far the most efficient way there is. it would be completely foolish to use resistors to control current flow. the difference between a resistor and an inductor are night and day and the inductor is the only way to control current non destructively and the fact that heat produced with resistors is non recoverable.
bench work is not cheap in uncharted territory.
Marathonman
|
|
|
|
Post by Marathonman on Jan 16, 2020 12:30:56 GMT -6
The Lenz’s law is a universal law of the Universe and there is no escape from it. Because of the standardization in the construction of today’s electric machines, the effect of this law is to transmit any opposing disturbances generated by a connected load back to the source in the form of reverse torque. Lenz’s law is the main justification for stating that electrical machines cannot operate with efficiencies greater than 100%. The standardization in the construction of electric machines (transformers, generators, and motors) is enforced by organizations such as ANSI/IEEE, NEMA, IEC, Patent Offices etc. these were put into place by our Government as a form of control with influences from big Oil Corporation and the Banking Cartels. these are put into place to maintain the massive cash flows from it’s citizens to the powerful elite robbing them of their hard earned wages.
it is quite obvious that electrical devices can be built with outputs exceeding the input that reach the global numbers of 40,000 and 10,000 in the US a lone only to be stolen by the Patent Offices under the guise of National Security. the patent office is not associated with the Governments so why they are allowed to do so is beyond me.
Free-energy technology is not meant to be controlled by vain and greedy parasites who wish to use a gift of God to exploit their fellow man.
Quote for one of the Patents; "and as the current flowing through them is reducing or increasing in intensity according it passes by more or less turns of the resistor, and therefore, in continuous variation; since we have done a continuous and organized variation we have achieved a constant change in the current which crosses the magnetic field formed by the electromagnets N and S and whose current, after completing their task in the different electromagnets, returns to the source where it was taken.
"AS IT PASSES BY MORE OR LESS TURNS OF THE RESISTOR" which solidifies what i have been saying that "R" does not exist and is just winding or loops of wire around Part G's iron core as the brush makes contact with the conductor as it rotates. each "LOOP" added or subtracted are the CEMF or BEMF produced by the loops that magnetically link to each other that increase or decrease as the brush rotates. since both set N and set S are directly connected to the ends of the resistance the current flowing through them is regulated by the Inductor controller Part G. this one large inductor controller is split into two halves from the two current feeds with two North opposing fields at the positive brush. what this does is allow the two feeds to be in complete unison yet remain separate 180 degrees out from each other, one increasing, one decreasing.
Do a simple test on your bench. take a straight core and wind it with 40 to 50 winds of wire then take a contact of some sort attaching the positive wire from the power supply. take the negative wire attaching both bulbs to one side then to both ends of the wired core. take the brush and sweep it from side to side and enjoy the alternating light show of inductive reactance hard at work reducing and increasing the current flow.
congratulations you just build a rudimentary part G with no commutator bars in site.
Regards,
Marathonman
|
|
|
|
Post by creasysee on Jan 17, 2020 0:40:13 GMT -6
Hi Marathonman! I think this: and this: "R" which is just a representation of some resistance withing Part G some different. Sorry, I think you not need to use the first sentence, use the second only, please. When you said this (the first sentence) me in first time, I was confused. The second sentence is better reflect how the device works and more easy to understand. Yes, I agree and understand that "R" doesn't exist as separate part of the device. Many thanks, creasysee |
|
